specifications subject to change without notice. all dimensions in inches. ? copyright 1998 the connor-winfield corporation 2111 comprehensive drive aurora, illinois 60505 phone: 630- 851- 4722 fax: 630- 851- 5040 www.conwin.com 2111 comprehensive drive aurora, illinois 60505 phone: 630- 851- 4722 fax: 630- 851- 5040 www.conwin.com 2.8v lvcmos surface mount crystal clock oscillator 5116 xo the connor-winfield models 5116, 5126, and 5136 are 7.5mm x 5mm, 2.8v lvcmos, surface mount, fixed frequency crystal oscillators (xo) designed for use in all applications requiring precision clo cks. this oscillator features low stand-by current (10ua) when the output is disabled. the rohs compliant, surface mount package is designed for high-density mounting and is optimum for mass production. operating specifications parameter minimum nominal maximum units notes frequency range (fo) 1.8 - 80 mhz frequency tolerance - ppm 1 5116 -25 25 5126 -50 50 5136 -100 100 operating temp range 0 - 70 c supply voltage (vdd) 2.66 2.8 2.94 vdc supply current (icc) 1.8 to 31.999 mhz - - 12 ma 32 to 50 mhz - - 20 absolute maximum ratings parameter minimum nominal maximum units notes storage temperature -55 - 125 c supply voltage (vcc) -0.5 - 7.0 vdc features: 1.8 to 80 mhz 2.8v operation rohs compliant tri-state enable / disable function overall frequency tolerance: 5116 25 ppm, 5126 50 ppm, 5136 100 ppm temperature range: 0 to 70c power saving stand-by current ceramic surface mount package tape and reel packaging bulletin sm075 page 1 of 2 revision 01 date 15 april 2002 input characteristics parameter minimum nominal maximum units notes enable voltage - (vih) 70% vdd - - vdc 2 disable voltage - (vil) - - 30% vdd vdc enable time - - 10 ns disable time - - 150 ns output disable current (lcc) - - 10 ua hcmos output characteristics parameter minimum nominal maximum units notes load - - 15 pf voltage high (voh) 2.39 - - vdc low (vol) - - 0.29 current high (loh) -4 - - ma low (lol) - - 4 duty cycle at 50% of vcc 45 50 55 % rise / fall time 10% to 90% - - 5 ns start-up time - - 10 ms jitter - - 5 ps rms notes: 1. inclusive of calibration @ 25c , frequency vs temperature stability, supply voltage change, load change, shock and vibration , 10 years aging. 2. oscillator requires a pull up resistor from pin 1 to vcc to insure proper operation. us headquarters: 630-851-4722 european headquarters: +353-61-472221
specifications subject to change without notice. all dimensions in inches. ? copyright 1998 the connor-winfield corporation 2111 comprehensive drive aurora, illinois 60505 phone: 630- 851- 4722 fax: 630- 851- 5040 www.conwin.com bulletin sm075 page 2 of 2 revision 01 date 15 april 2002 pin connections 1: enable/disable 2: ground 3: output 4: vcc oscilloscope freq counter osc power supply input for e/d probe meets eia-481a and eiaj-1009b 2,000 pcs/reel bypass capacitor, c-by, should be ceramic capacitor .01 uf symmetry soldering general conditions 260c max x 10 sec max x 2 times max or 230c max x 180 sec max x 1 time typical operation data (vapor phase reflow) 20 to 100 sec up to 215c, 50 sec at 215c, then down to room temperature per 1 to 5c / sec environmental characteristics temperature cycle the specimen shall meet electrical characteristics after tested 5 cycles of -55c / 30 minutes and +125c / 30 minutes hermetical no bubbles appear in flourinert (fc-43) at 125c 5c for 5 minutes solvent resistance marking will withstand immersion in isopropyl alcohol or trichloroethylene suggested pad layout ordering information 5116 - 77.76 mhz clock series center frequency mechanical characteristics free drop the specimen shall meet electrical characteristics after tested 3 times, free drop testing on the hard wooden board from a height of 75 cm. vibration the specimen shall meet electrical characteristics after tested by the following conditions: 10-55hz 1.5mm amplitude, 55-2000 hz 20 g's, 2 hours for each plane thermal shock after applied thermal shock of 260c max x 10 sec max x 2 times, or 230c max x 180 sec max, the specimen shall meet electrical characteristics solderability (eiaj-rcx-0102.101 condition 1a) 1) flux: mil-f-14256 (ww rosin=25%, isopropyl alcohol = 75%) 2) solder: qq-s-571 (sn = 63%, pb = 37%) 3) solder bath temperature: 235c 5c 4) depth of immersion: up to electrical terminal 5) immersing time: within 2 sec 0.5 sec into solder bath after performing the above procedures, a newly soldered coverage shall be greater than 90% after performing the above procedures, a newly soldered coverage shall be greater than 90% after performing the above procedures, a newly soldered coverage shall be greater than 90% after performing the above procedures, a newly soldered coverage shall be greater than 90% after performing the above procedures, a newly soldered coverage shall be greater than 90% test circuit output waveform tape and reel dimensions package characteristics package hermetically sealed ceramic package and metal cover dimensional tolerance: .02" (.508mm) .005" (.127mm)
|
